It is currently Sat Oct 05, 2024 2:11 am


All times are UTC - 8 hours [ DST ]




Post new topic Reply to topic  [ 51 posts ]  Go to page 1, 2, 3, 4, 5, 6  Next
Author Message
 Post subject: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Wed Mar 30, 2011 11:48 am 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
In the spring of 2007, I ended up buying a white 1992 240SX coupe for $500 to initially fix and flip to make some money, but I ended up liking it better than my red car, so I took my entire spring break and swapped everything over from the red car to the white car. It took me about 50 man hours to do everything. Interior, suspension, diff, transmission and engine, wiring, brakes, and all the other things were swapped over. It was a big undertaking!

Image

Image

Image

Image

Blown engine pulled out and ready for the SR.

Image

Image


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Wed Mar 30, 2011 12:06 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
These were taken April 28th, soon after I swapped everything over from the red car.

Image

Image

These pictures were taken May 12th of 2007 at the Redding, CA Drag Strip.

Image

Image

The car stayed as it was after I did all the parts swapping for some time. I started saving and buying parts for the next step of my build. More power!!!


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Wed Mar 30, 2011 1:21 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
Ordered some new goodies for the next part of the project.

Kaaz 1.5 way LSD, ACT HD pressure plate, ACT 6 puck racing clutch, ACT Streetlite flywheel, and a new radiator (wish I would have just ordered another Koyo), because my koyo was damaged.
Image

Splitfire Coil Packs
Image

Tomei 740cc injectors, Tomei/Nismo adjustable FPR, oil filter relocation kit, Earls top mount turbo lines, Tial Q BOV, cheap catch can, Nismo engine and tranny mounts, and some other hardware.
Image

And where the money was spent! Full-Race twin scroll GT3071R, Full-Race twin scroll turbo manifold, Tial 44mm waste gate, and a Full-Race 3" down pipe.
Image


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Wed Mar 30, 2011 1:28 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
Time to pull out the motor!

11-16-07
Image

11-20-07
Image

Image

Image

Image

Then I had to wait for awhile for the above parts to come in (I actually pulled the motor first).

06-17-08

Dirty motor
Image

Image

Cleaned up a little, and with new turbo stuff mounted.
Image

Image

Image


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Wed Mar 30, 2011 1:36 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
07-09-08: Engine is all put back together!
Image

Image

Image

Image

New driveshaft (1 piece AL), and ACT setup.
Image

Bolted up and ready to go.
Image

07-10-08: Engine bay ready for motor.
Image

07-12-08: Engine is in (again)!
Image

Image

08-01-08: Ready to rock!
Image

Image

Image

Image

Image

With the splitfire coil packs installed. Can't run the cover anymore :cry:
Image


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Wed Mar 30, 2011 1:57 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
09-10-08: Took some current pictures of what the car looked like.
Image

Image

Image

Image

Image

03-26-09: I got some new wheels finally!
Image

Image

Then I installed some 275/40/17 tires on the rear.
Image

Image

Image

05-07-09 I finally was able to make it to a dyno!
Image

Image

Image

It was a mustang dyno and the elevation was at 4200 ft. I put down 342.5 whp and 334.6 lb-ft of torque! The stock cams really hurt my power up top!
Image

With this power, I was able to run an 11.95 @ 114mph with a 1.61 60' launch. That is my best time so far at the drag strip.


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Wed Mar 30, 2011 2:05 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
05-30-09: I did a "photoshoot" down on treasure island in the bay area. My friend Bryan To shot all of these pictures. This is also how the car sat before I pulled the motor (again) for the current build.

Image

Image

Image

Image

Image

Image

Image

Image


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Wed Mar 30, 2011 2:11 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
The next part of my build continues.

09-21-09: The car is parked and the next engine swap is started.
Image

Image

Image

New accessory pulleys
Image

ATI Super Damper
Image

Tomei 260 duration 12mm lift cams
Image

09-22-09: Engine is pulled (again)
Image

Image

10-01-09: Bought some megan coilovers. I now wish I would have spent the extra money on a good set of coilovers like KW (what I plan on getting now).
Image


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Wed Mar 30, 2011 2:18 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
Now a little story: So I ended up buying another block to do my "build" on originally. I had it machined, and the rotating assembly installed (just the block), and then I installed the cylinder head and all the other parts I had ordered up to this point. The engine had scat rods, Mahle pistons, a brand new SR20DE crank, ACL bearings, Apexi HG, all the head hardware etc. I ran out of money towards the end of the build and stupid me cheaped out on the tune. I paid for my stock ECU to be modified and re-flashed for a tune capable of my modifications and boost parameters. The initial engine break in went decent, and my AFRs looked to be good (a little on the rich side except for when at 20psi and higher rpm). Well about 600 miles into breaking in the motor, the tune showed its ugly self and detonated badly and blew out the ring lands on number one mainly, but a little on two and three pistons. Number 4 was the only one still in great shape. I also had a lot of problems with the block sealing correctly with the coolant fittings that were pressed in the block. So I decided to scrap that motor, and am now currently building the original motor that I bought back in 2005. From now on, all updates will be of this motor.


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Wed Mar 30, 2011 2:24 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
01-11-11: Brand new Greddy intake manifold!
Image

01-21-11: New CP 9:1 86.5mm pistons.
Image

02-10-11: Separating the SR20 that I bought back in 2005 for the first time! This motor had 140k miles on it from me alone, so with an estimated 200k on the clock after whatever miles were put on it in Japan, this thing still ran perfect! It had factory compression before being pulled, and the bearings look amazing after I pulled the crank. I've always used Royal Purple motor oil.

Image

03-02-11: Mazworx Tq Plate!
Image

WPC treated parts
Image

WPC treated CP pistons
Image

As of 03-30-11 (today): The motor is in the machine shop getting prepped for assembly. More updates soon!!!


Top
Offline Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 51 posts ]  Go to page 1, 2, 3, 4, 5, 6  Next

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Theme created StylerBB.net