It is currently Mon Nov 11, 2024 7:15 am


All times are UTC - 8 hours [ DST ]




Post new topic Reply to topic  [ 51 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6  Next
Author Message
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Sun Mar 18, 2012 5:09 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
Update: checked the solid lifter lash, and I have two that are grossly out of spec. Car is benched until I can get it fixed.


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Fri Sep 07, 2012 4:19 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
Ordering new valves and guides soon, so hopefully some updates will be in the mix.


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Wed Sep 26, 2012 7:08 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
The new valves came in! Ferrea +1mm oversized valves on both intake and exhaust. Also got the Ferrea valve locks to go with them. Wasn't cheap, but it's a good product. Working on getting the cylinder head pulled so I can get them all to a machine shop! Getting excited again, ha ha.

Image

Image


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Mon Oct 15, 2012 8:28 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
Just got the Cams and Valves back from WPC Treatment!

Image

Close up shot of the "used" Tomei 260 Intake Procam
Image

Close up of the exhaust side +1mm Ferrea valve
Image

Head is ready to pull, going to do it tomorrow!
Image


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Thu Nov 15, 2012 7:29 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
Finally getting some progress!

Got some pictures back today from the machine shop. The cylinder head has been ported and cleaned up a little so far (more work to be done still). Valve guides are installed, but not the valves yet. I just hope everything goes smoothly, lol. I'm tired of not having this car running!!!

Image

Image


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Fri Feb 15, 2013 8:27 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
Well, I got some numbers back from Port Flow Design (shop that is working on my cylinder head). I should hopefully get my cylinder back from them soon!

Here's the cylinder head after the port work and such. I had them also install the +1mm Ferrea valves and supertech bronze valve guides.

Image

Image

They also bench tested my cylinder head. I honestly forgot to have them flow test it as stock, so I'm pretty bummed about not having stock numbers to compare it to, but I do have numbers (from them) from when they tested a stock SR20VE cylinder head. I know the SR20VE head is much better than the standard highport DET head (especially after some work), but I just couldn't afford to make the swap. However, I'm fairly happy with the results I got back from the DET head. Looks like the exhaust side flows a tad better than a stock VE head now, but still lacking a little up top for the intake side. I'm OK with that though. I know other people have gotten different numbers for both heads, but I figured since these were both tested by the same company on the same equipment, that it would be a reasonable comparison. Here's a little chart I put together comparing the two:

Image


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Thu Feb 21, 2013 11:32 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
Received my cylinder head today from Port Flow Design. Here are a couple snap shots:

Image

Image

Image

Image


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Fri Feb 22, 2013 11:12 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
Got the head installed with all the valvetrain. More tomorrow. Hopefully going to have this done by next weekend!


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Sat Mar 02, 2013 11:51 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
Well, it's not running yet, but hopefully soon! Going to be working on it some more tomorrow. It's getting close!

Image


Top
Offline Profile  
 
 Post subject: Re: 2007-Current: My 1992 240SX Coupe Project
PostPosted: Sun Mar 03, 2013 11:30 pm 
Site Admin

Joined: Mon Mar 28, 2011 11:58 pm
Posts: 78
Well, it's "basically" done! Ha ha

Image

I haven't fired it up yet. I still need to put oil in it, and hook up the battery. Going to crank it a bit to build oil pressure, then connect the injectors and CAS and fire it up. Warm it up for awhile, then rip the VC back off and check the shims. After that, I'll order new shims if I have to (may not, I have a lot already, lol). I'll put them in, and then I'm ready to rock! If I'm lucky, I can drive it next weekend!


Top
Offline Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 51 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6  Next

All times are UTC - 8 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
Theme created StylerBB.net